Subsequent 37: Assign Aftertouch to Filter

Everything Sub.
Post Reply
mpaulcurreri
Posts: 16
Joined: Sat Nov 24, 2018 4:20 pm

Subsequent 37: Assign Aftertouch to Filter

Post by mpaulcurreri » Wed Apr 17, 2019 8:15 am

Hi guys --
I seem to be getting very very old. For the life of me I cannot recall how to simply assign aftertouch to affect the FILTER. Not one of the LFOs, just the filter. Could someone please remind me? And could you hurry? I seem to be aging extremely rapidly, and I don't know much time I have left. ;)

User avatar
_DemonDan_
Posts: 1249
Joined: Mon Nov 16, 2009 4:52 pm

Re: Subsequent 37: Assign Aftertouch to Filter

Post by _DemonDan_ » Wed Apr 17, 2019 10:46 am

mpaulcurreri wrote:I cannot recall how to simply assign aftertouch to affect the FILTER. Not one of the LFOs, just the filter.

Hi mpaulcurreri,

In the SUB37, SSQ37, SSQ37CV world, Aftertouch only modifies the depth of another Source.

It can not be directly assigned to a parameter knob.

So... what you do is make the MOD Source CONSTANT (always on), make the Destination FILTER, and then use the MOD CONTROL page to set AFTERTOUCH: +100%.

Then, while fully pressing a key's Aftertouch, set the FILTER AMT knob to the maximum desired amount.
_ :twisted: _DemonDan_ :twisted: _

mpaulcurreri
Posts: 16
Joined: Sat Nov 24, 2018 4:20 pm

Re: Subsequent 37: Assign Aftertouch to Filter

Post by mpaulcurreri » Wed Apr 17, 2019 11:27 am

Hi Demon Dan.
You are a very friendly Demon, Dan.

I really appreciate your comments. I hate to tumble backwards back into the noob womb, but could you be more specific about how to do these first two steps?

1. Make the MOD Source CONSTANT (always on)
2. Make the Destination FILTER

Where are these parameters located?
Thanks man,
Paul

User avatar
_DemonDan_
Posts: 1249
Joined: Mon Nov 16, 2009 4:52 pm

Re: Subsequent 37: Assign Aftertouch to Filter

Post by _DemonDan_ » Thu Apr 18, 2019 9:05 am

mpaulcurreri wrote:Could you be more specific about how to do these first two steps?

1. Make the MOD Source CONSTANT (always on)


SSQ37 Manual - Bottom of page 50 PGM SRC: CONST ON

mpaulcurreri wrote:2. Make the Destination FILTER

SSQ37 Manual - Pages 22-23 FILTER AMT

And, to apply Aftertouch
SSQ37 Manual - Middle of page 50 AFTERTOUCH
_ :twisted: _DemonDan_ :twisted: _

mpaulcurreri
Posts: 16
Joined: Sat Nov 24, 2018 4:20 pm

Re: Subsequent 37: Assign Aftertouch to Filter

Post by mpaulcurreri » Sun Apr 21, 2019 1:27 pm

Thanks Dan!

Quatschmacher
Posts: 74
Joined: Sun Jan 28, 2018 7:03 pm

Re: Subsequent 37: Assign Aftertouch to Filter

Post by Quatschmacher » Tue Jun 04, 2019 10:28 am

Couldn’t you also use source “pressure” and destination “filter”?

User avatar
_DemonDan_
Posts: 1249
Joined: Mon Nov 16, 2009 4:52 pm

Re: Subsequent 37: Assign Aftertouch to Filter

Post by _DemonDan_ » Thu Jun 06, 2019 11:34 am

Quatschmacher wrote:Couldn’t you also use source “pressure” and destination “filter”?

Hi Quatschmacher,

You're completely correct. It's been a while since I've scrolled through that Source list and I completely forgot that Pressure was a Modulation Source as well as a multiplier.
_ :twisted: _DemonDan_ :twisted: _

Post Reply