Changing the backlight EL panel

[Psychlist1972]

I got a great deal on a used voyager, but I'm not a fan of the panel backlight color. I love everything else about it.

Does anyone know if the backlight EL panel is a part (or parts) that can be replaced with a different color? Or is the color coming from the front panel sticker? I haven't yet opened it up to see.

I do a lot of electronics work, so technically I'm fine with doing a replacement if it's possible. I'm also not concerned about opening something up and tinkering a bit. Even a Voyager. (well, except for that 6 layer voice board).

I assume what's in there is a bigger version of something like this, but with a lot of holes in it.
http://www.adafruit.com/products/414

Thanks.

Pete

[Psychlist1972]

Actually, I see it's all part of the sticker.

I found this out because mine front panel sticker is lifting / bubbling in a number of places. I can easily take off the whole middle white voyager sticker, and with some slight effort, likely the rest.

Is that normal?

Pete

[paramnesia]

the blacklight is a separate layer from the adhesive overlay: chassis metal, then blacklight ribbon, then top adhesive overlay

where the blacklight flat ribbon changes 90 degrees into the chassis, there may be a sticker bump, like near the touch surface - press down to reseat or place weight on it overnight

i don't think the color is changeable, you would have to undo all the top panel hardware (knob shaft lock nuts) then rip the overlay off, and that would most likely damage or tear the really fragile blacklight ribbon

you might try re-glueing with something safe that does not melt the plastics

[Psychlist1972]

Thanks.

Mine does not appear to be set up like that. The whole sticker, which includes the backlight layer integrated, is coming off of the metal in a number of places. I haven't seen where it goes into the chassis yet. The bubbles are all over.

Pete

[paramnesia]

Thanks.

Mine does not appear to be set up like that. The whole sticker, which includes the backlight layer integrated, is coming off of the metal in a number of places. I haven't seen where it goes into the chassis yet. The bubbles are all over.

Pete

would you be willing to post a photo?
moog service may be able to sell you a different color if contacted with the bubble issue

[Psychlist1972]

Thanks.

Mine does not appear to be set up like that. The whole sticker, which includes the backlight layer integrated, is coming off of the metal in a number of places. I haven't seen where it goes into the chassis yet. The bubbles are all over.

Pete

would you be willing to post a photo?
moog service may be able to sell you a different color if contacted with the bubble issue

The lifting is hard to photograph because it's in the middle of the panels in most cases and you can feel it more easily than photograph it. The central panel is the worst of the bunch, though. It comes right off with no effort.





This can likely be fixed with glue if I want to, but I emailed service last night to see if I can get replacement stickers (I'd pay for them) in a better color anyway.

Pete

[Vince Ascoli]

Greetings, Pete! Judging from the pics, if that's a maple wood body with Jade green lighting, then I'm afraid there is no 'better' color only one you may like better personally. Goofing aside, I've got two Voyagers, a Maple Jade and one of the recent (blue) Aluminums and love the hell out of both...duophony w/ poly chain is especially terrifying. Finding this interesting and looking forward to see how this progresses for you, thanks!

[Control_Voltage]

Hello everyone!!!


Here is a helpful document for correcting minor peeling in the overlays of older Voyagers:
http://seamslikereality.com/moog/Voyage ... Gluing.pdf

However, if you are having the entire two layers of overlay and backlight peel away from the unit entirely as shown in the above post, this will require the attention of an Authorized Moog Tech to correct properly.

Please contact us directly:

Andy Hughes, Service Manager
andy@moogmusic.com
828-251-0090 xt 221

Nate Marino
natemarino@moogmusic.com
xt. 204

Taylor Mott
taylor@moogmusic.com
xt. 217

Thanks,
Andy Hughes
Moog Tech Support

[Psychlist1972]

Thanks Andy

I mailed you last week about the peeling/replacements (ans changing the color). I'm happy to (and would rather) do it myself if possible.

Pete