Moog Music Forum

Guitarists and bassists online are always talking about signal loss or interference in (unbalanced) instrument cables over longer run lengths (often above 20ft), apparently because passive guitars and basses are considered high impedance devices. Since synths are line level devices, do we have to wo...

I ended up getting the electrical engineer to have another look at both of my Slims and he hunted down/replaced/re-soldiered various shorts or damaged components (different issues for each unit) and now I can run my units perfectly again! Just getting some replacement timber sides made for the stick...

stiiiiiiive wrote: ↑Wed Nov 11, 2020 8:06 am They offer the CV out mod possibility; I talked to them lately
Unfortunately, this is not the right time for me... but please provide some feedback if you decide to order.

Will do! I just ordered some!

I need to replace my side panels too.

I found these ones:

https://2manysynths.nl/shop/moog-little ... -stage-ii/

Not exactly Moog Walnut but might still be cool.

Whatever I end up doing, I need to accommodate the CV Output Mod too..

David

Ah yes, I could try reinstalling the firmware - good idea! I've also contacted Moog Music tech to get their thoughts.

Will keep ya updated..

spacing should have a dramatic effect, when you pan it if you enable the visual feedback in the display, can you see the values changing as you turn the knob? ps set filter cutoff to around noon Yea I have the visual feedback on in the display and the values do change, but there is no difference in...

I just messed with mine for a bit: -spacing -filter cutoff -amount to filter knobs all interact significantly, and I could lose one stereo channel easily by adjusting them. hopefully that's all it is? good luck! Thanks for taking the time to run tests and provide tips - I appreciate it! I have been...

Cool thanks - I'll experiment with the filter spacing control for the patches in which it happens and report back.

Hi there, I have noticed recently that when using my Voyager XL in stereo (using 2x jack outputs, or headphones from the headphone output), the signal will cut out to one side only depending on the filter mode (dual LP = one side only, LP/HP = both sides). I understand different filter modes give a ...

Sounds like you found a solution. I use a midi clock with mine. It works well. I'm interested in using MIDI clock too. Have you typically been able to get very long delay lengths (whole note etc.) via MIDI clock? I'll have to have a play around.. For a live band application, I was thinking tapping ...

Cheers for your help stiiiiiiive. After further testing, yes there seems to be a lower limit where the tapping doesn't register as a delay time, however your idea to tap while in short mode and then switch to long mode got me the delay lengths I'm looking for. Interesting sound for vocals though.. I...

Hey there, I've got this idea to use one of my two MF-104M's as a vocal delay, routed from an Aux send on my mixing desk. I want whole note length delays (i.e. one delay per bar) to match my VST/DAW delays, but in a live performance situation. I'm having trouble tapping the delay time this slow.. Is...

Somewhere in my quest for Phatty knowledge someone mentioned that feeding an external clock to the Phatty chain can contribute to the note-drop effect. I have found this to be true. It may have been me :) I remember performing some tests and filtering the MIDI clock signal led to far better results...

Do you get any note drop-out or double-up glitching issues?

I have 3 phatty voices and it never was reliable with the round-robin note distribution.

EDIT: Just read in your link that for you this issue seemed to be related to MIDI merge - thanks, I'll look into that for my set-up!

David
NZ

New Moog Matriarch - arp/seq, 4osc paraphonic, stereo filter/stereo delay, semi-modular synth. Looks like Grandmother's big brother: https://www.moogmusic.com/news/introducing-matriarch?fbclid=IwAR0fLRCJDls9MpnFcC2Z_eNcpwtpcUlto5KwSUnRQJTyVCHV8fDfRhmSI_k https://api.moogmusic.com/sites/default/files...