Search found 1103 matches

by till
Mon Nov 11, 2019 8:51 am
Forum: Minimoog Forum
Topic: Voyager Midi In/Midi Out Problem upon restart?
Replies: 4
Views: 67

Re: Voyager Midi In/Midi Out Problem upon restart?

Hi,
it is not like this here. Strange. I am not aware of a way parameter to switch this from one to another way it works.
What firmware version is on your Voyager? Maybe it was a bug on an outdated version.
by till
Sun Nov 10, 2019 10:39 am
Forum: Modular Forum
Topic: Moog Voyager RME - Unable to update to v.3.5
Replies: 2
Views: 72

Re: Moog Voyager RME - Unable to update to v.3.5

... The only other thing I'm not sure about is if the SysEx Device ID is set correctly? At the moment is number 88... I don't know if that can cause any problem, but I couldn't find any setting on MIDI-OX to check that it's sending the SysEx file to the correct MIDI device? ... You should always us...
by till
Fri Nov 08, 2019 3:12 pm
Forum: Moog One
Topic: loud Popping from inside of the Moog one - anyone else?
Replies: 5
Views: 114

Re: loud Popping from inside of the Moog one - anyone else?

Here too, but only sometimes.

I think these are the inlay panels left and right of the display sections. These panels sit in a frame that is as long as the whole panel. And the heat from below expands the frame and the panels. But most likely not at the very same amount.
by till
Sat Nov 02, 2019 5:00 pm
Forum: Sub 37, Subsequent 37, Sub Phatty Forum
Topic: Sub Phatty Editor update for MacOS Catalina
Replies: 4
Views: 98

Re: Sub Phatty Editor update for MacOS Catalina

HumanByDesign wrote:
Sat Nov 02, 2019 11:32 am
...Has anyone actually been able to install it on Catalina yet?...
Me. Today. No problems.
by till
Sat Nov 02, 2019 4:58 pm
Forum: Moog One
Topic: do the Moog One knob values "jump" when you move them, after loading a patch?
Replies: 9
Views: 785

Re: do the Moog One knob values "jump" when you move them, after loading a patch?

All three modes have their week points. The PASS THROUGH will first do nothing and then suddenly there is a change. So changing it live with a sound parameter you don't know where it is set at the playing sound, you don't know when the change will actually start to take place when you move the pot s...
by till
Sat Nov 02, 2019 6:01 am
Forum: Sub 37, Subsequent 37, Sub Phatty Forum
Topic: Sub Phatty Editor update for MacOS Catalina
Replies: 4
Views: 98

Re: Sub Phatty Editor update for MacOS Catalina

The newest available (I am registered and logged in) editor for the SubPhatty is version 2.0.0 and 64 bit. So it does run on the MacOS Catalina. The download is bundeled with the win version and the SubPhatty firmware version 2.2.0 .
by till
Wed Oct 30, 2019 3:24 pm
Forum: Minimoog Forum
Topic: Voyager transposing issue
Replies: 2
Views: 135

Re: Voyager transposing issue

... I discovered that when I eject an external hard-drive from computer B in my rig it sends a sysex message and 3 pitch messages on ch1. Perhaps this is the cause. I have now moved the offending Voyager to run on ch3 (hopefully thereby avoiding the sysex), ... SysEx is send global, not per MIDI ch...
by till
Tue Oct 22, 2019 5:28 pm
Forum: Minimoog Forum
Topic: Minimoog Key Issue
Replies: 3
Views: 380

Re: Minimoog Key Issue

Repairing a Fatar keybed is not that easy. And as you easily do harm to the aftertouch ribbon connector cable (it is more like a flat thin plastic with metallic zick-zack printed on it). These Fatar keybed don't use contacts like the old vintage ones. you need to deassemble the key to reach it. And ...
by till
Mon Oct 21, 2019 9:00 am
Forum: Minimoog Forum
Topic: Minimoog Voyager Clicks and Pops
Replies: 8
Views: 862

Re: Minimoog Voyager Clicks and Pops

...t has the latest firmware installed - V3.5. I know there is a further version but I would rather not install that one as it is still in Beta stage. ... It is in "beta" for nearly 8 years now. In fact it is working all fine here. Moog did not officially released it, as the Voyager software were n...
by till
Mon Oct 21, 2019 8:51 am
Forum: Minimoog Forum
Topic: Minimoog tuning goes slightly sharp during amp release
Replies: 2
Views: 315

Re: Minimoog tuning goes slightly sharp during amp release

Is it also happening when you switch the VCO modulation to the left of the VCOs off? If yes, it appears to be a hardware error. If not, check the most left switch in the lower controller section: is is set to filter envelope modulation? The modwheel zero position might no shut-off all modulation in ...
by till
Wed Oct 16, 2019 3:45 pm
Forum: Moog Music General Topics Forum
Topic: Moog synthesizer model comparison
Replies: 7
Views: 1468

Re: Moog synthesizer model comparison

A list of modules for the Modular Model 10, 12, 15, 35, 55, IIIp in normal default configuration might be useful too.

Mmmh, I need some time besides turning the knobs ...
by till
Tue Sep 24, 2019 4:57 pm
Forum: Minimoog Forum
Topic: Model D reissue, Keyboard tuning error NOT working?
Replies: 40
Views: 10052

Re: Model D reissue, Keyboard tuning error NOT working?

... is it possible to export a firmware file, via sysex? Yes. See the SysEx manual: ADDITIONAL SYSEX COMMANDS TRANSMIT FIRMWARE F0 04 15 7F 16 00 00 00 F7 (Hardware will output keyscan firmware image in SysEx format; can be saved & used to program another keyscan board if needed) I never tried it. ...
by till
Tue Sep 24, 2019 1:10 pm
Forum: Minimoog Forum
Topic: Model D reissue, Keyboard tuning error NOT working?
Replies: 40
Views: 10052

Re: Model D reissue, Keyboard tuning error NOT working?

So this answer from Moog is about the same the Taurus 3 users received when asking for a bug free firmware. And guess what: it was due to the Minitaur needeing full attention. but right after this, we would get the update. And nothing happened. For several years! Still waiting.
by till
Mon Sep 23, 2019 2:57 pm
Forum: Minimoog Forum
Topic: Model D reissue, Keyboard tuning error NOT working?
Replies: 40
Views: 10052

Re: Model D reissue, Keyboard tuning error NOT working?

From the 1.8 change log: New in 1.8.0 • Prior to 1.8, when using your Minimoog Model-D as a midi controller, pitch wheel data was offset from the original note value. 1.8 fixes this issue. ... does Moog have a changelog documenting the updates, between firmware versions? that is normal in most indus...
by till
Fri Sep 20, 2019 5:07 pm
Forum: Minimoog Forum
Topic: Model D reissue, Keyboard tuning error NOT working?
Replies: 40
Views: 10052

Re: Model D reissue, Keyboard tuning error NOT working?

... It seems early production they had it and later it was missed off ..I'm unable to check which firmware I have but my Minimoog Model D is showing passed QC July 2017 Presume 1.8 ... You can check the firmware version via SysEx From the manual: TRANSMIT FIRMWARE VERSION F0 04 15 7F 15 00 00 00 F7...