Need a cheap way to attenuate a signal?
-
- Posts: 62
- Joined: Thu Mar 11, 2010 12:07 pm
- Location: Boise
Need a cheap way to attenuate a signal?
If you're handy with a soldering iron, you can do it with a pot(50k Lin is good). If not, this passive mixer works very well. I find that it compliments the CP-251 very well. http://www.sweetwater.com/store/detail/SplitMix4/. edit-note that the pots are audio tapered.
Last edited by Benjamin AM on Tue Mar 23, 2010 10:56 am, edited 1 time in total.
Little Phatty Stage II, Rogue, Cp-251, Soldering Iron
-
- Posts: 1279
- Joined: Fri Feb 02, 2007 2:17 am
- Location: Illinois(e)
Hey, thanks for suggesting the SPLITMix4. I think it could also be used as an alternative control input for Nord Modular synths:
http://electro-music.com/forum/viewtopic.php?t=32424
The specs don't mention it, but I assume that the SPLITMix4 has audio taper pots. Can you tell if they are audio or linear taper?
http://electro-music.com/forum/viewtopic.php?t=32424
The specs don't mention it, but I assume that the SPLITMix4 has audio taper pots. Can you tell if they are audio or linear taper?
varice
-
- Posts: 62
- Joined: Thu Mar 11, 2010 12:07 pm
- Location: Boise
In retrospect
I don't know how I overlooked the fact that the pots are Audio(Log) tapered. Now that you mention this, I do notice that the signal is heavy on the end. I opened it up to see how easy it would be to replace the pots with linear tapers. To my disappointment I found that they are the dual ganged(stereo) panel mount type (100k-A). Anyhow, I am going to replace them with dual ganged 50k linear pots that I found at Small Bear(http://www.smallbearelec.com/Detail.bok?no=736). Unfortunately they are not panel mount but they'll work. I'll let you know how it turns out.
Little Phatty Stage II, Rogue, Cp-251, Soldering Iron
Audio taper pots are not all bad though. They can give you more control range of small amounts of modulation, such as when you want to add just a little LFO vibrato CV to the pitch of a VCO or the cutoff of a VCF...
Thanks again for the suggestion. I've been looking out for a low cost CV attenuator box. It seems that there are not many available.
Thanks again for the suggestion. I've been looking out for a low cost CV attenuator box. It seems that there are not many available.
varice
I've got the DOD resistance mixer 240. 4X1 mono device. There is no board it is all discrete devices. Very easy to add more 1/4" jacks or change some of the pots from A to L.
Link: http://www.dod.com/accessories/accessories.htm
Link: http://www.dod.com/accessories/accessories.htm
"Music expresses that which can not be said and on which it is impossible to be silent."
Thanks much for the pic... It confirms for me that the box wiring is optimized as a 4 input to 1 output mixer. To optimize it for use as a 1 input to 4 output splitter function, it would need a little wiring modification.
A bit hard for me to tell from the pic and/or my laptop display - are the resistor color bands yellow-purple-RED-gold or yellow-purple-ORANGE-gold?
A bit hard for me to tell from the pic and/or my laptop display - are the resistor color bands yellow-purple-RED-gold or yellow-purple-ORANGE-gold?
varice
-
- Posts: 97
- Joined: Wed Dec 29, 2004 8:29 pm
- Location: Long Beach,Ca
- Contact:
-
- Posts: 62
- Joined: Thu Mar 11, 2010 12:07 pm
- Location: Boise
Hey Tubeampguy, thanks you so much for posting the pic. I made one of these with a 100k and it works awesome. One thing that I could not gather from the picture was where lug one was connected to.. I assumed to the housing, but when I soldered it this way there was no attenuation so I had to jump it over to the ground. Do you own any of these to check lug 1?
Little Phatty Stage II, Rogue, Cp-251, Soldering Iron
-
- Posts: 97
- Joined: Wed Dec 29, 2004 8:29 pm
- Location: Long Beach,Ca
- Contact:
Benjamin AM wrote:Hey Tubeampguy, thanks you so much for posting the pic. I made one of these with a 100k and it works awesome. One thing that I could not gather from the picture was where lug one was connected to.. I assumed to the housing, but when I soldered it this way there was no attenuation so I had to jump it over to the ground. Do you own any of these to check lug 1?
No I don't own these(sorry) I found this picture years ago (v.90 dial up modem) online.
The body of the pot might be isolated? Did you check it with a meter to see if there's continuity? Sometimes just the threaded area is the ground path.When its tightened down onto metal (like a control plate) It completes the circuit. You are right about pin 1 being ground. Signal comes in on 3, goes out 2(wiper) 1 is ground. 3 and 1 can be reversed to change CW to CCW.
[/i]
-
- Posts: 62
- Joined: Thu Mar 11, 2010 12:07 pm
- Location: Boise