Search found 218 matches

by acorkos
Wed Feb 24, 2010 3:42 pm
Forum: Minimoog Forum
Topic: I want a Voyager Old School
Replies: 43
Views: 7111

anoteoftruth wrote:Canadian stores always give us the crap end of the stick :(
it's 'cause you'se guys are a buncha hosers....

http://www.youtube.com/watch?v=GsgVspgy ... re=related
by acorkos
Sat Feb 20, 2010 11:38 pm
Forum: Moog Music General Topics Forum
Topic: Why do both Voyager and Phatty lack 1 OSC FREQ?
Replies: 6
Views: 927

Re: Why do both Voyager and Phatty lack 1 OSC FREQ?

MLPS2 wrote:On both synths not all Oscillators have Frequency control. Why is this?
from the voyager old school manual (p. 16): "Oscillator 1 performs as a master oscillator to which Oscillator 2 and 3 are tuned."

if you really need to, use the FINE TUNE control if you need to change OSC 1's frequency...
by acorkos
Wed Feb 17, 2010 4:19 pm
Forum: The Moog Guitar Forum
Topic: Sorry, but, could this guitar be any uglier?
Replies: 87
Views: 55497

MarkM wrote:I would take a saw to the upper black wing and amputate it.
unfortunately, that's where your forearm would rest. it might look lame, but it's necessary for comfort.
by acorkos
Tue Feb 16, 2010 3:55 pm
Forum: Minimoog Forum
Topic: Voyager Old School + Kenton USB Solo (Midi/CV convertor)
Replies: 1
Views: 897

any inexpensive digital multimeter (DMM) that reads DC voltage will tell you what's going on there. radio shack or any other electronics store has them. it's a nice tool to have around
Image
by acorkos
Wed Feb 10, 2010 2:06 pm
Forum: Taurus, Minitaur & Sirin
Topic: T3 amplification
Replies: 55
Views: 18141

Re: Update on my purchase of the Behringer TRUTH B2092A sub.

mayidunk wrote:...And the subs tend to be more felt at times rather than heard...
try it with a triangle wave, or a sine wave if you have one
by acorkos
Thu Feb 04, 2010 7:12 pm
Forum: Minimoog Forum
Topic: New Voyager OS problem
Replies: 12
Views: 3983

it's possible the keybed needs to be centered...your problem might be one of simple physical interference from the metal trim of the mod wheel assembly. check to see how close the low C key is to the metal trim. is there a slight gap between that lowest key and the metal trim, and is there a similar...
by acorkos
Sun Jan 31, 2010 3:37 pm
Forum: Taurus, Minitaur & Sirin
Topic: T3 amplification
Replies: 55
Views: 18141

my BFD speakers are about 2 years old. the floor monitors came from arizona, the sub and tops from michigan (=shipping$$$). the palm springs builder wasn't available at the time i ordered. the t39 was $800 plus packing/shipping. t39 included 22" width, 12LF driver, dual speakon connectors, recessed ...
by acorkos
Sun Jan 31, 2010 2:16 pm
Forum: Taurus, Minitaur & Sirin
Topic: T3 amplification
Replies: 55
Views: 18141

correct....speaker goes on the top left, facing left. you can see the route the sound travels...down, then up behind the speaker, down the back of the cab then out the front bottom left.... i purchased the plans, but i didn't think my woodworking skills were up to snuff. i paid one of the recommende...
by acorkos
Sun Jan 31, 2010 12:01 am
Forum: Taurus, Minitaur & Sirin
Topic: T3 amplification
Replies: 55
Views: 18141

i have a t39...22" wide w/Eminence Delta 12LF, powered by 500 watts from a bridged QSC RMX850. Check out this link regarding getting 6 to 12 db more volume from a sub up near a wall or pointed into a corner... http://billfitzmaurice.info/forum/viewtopic.php?f=1&t=398 and here's the innards of my t39...
by acorkos
Mon Jan 25, 2010 9:16 pm
Forum: Taurus, Minitaur & Sirin
Topic: T3 amplification
Replies: 55
Views: 18141

EricK wrote:I would love to see someone point me to a PA system or explain to me how to hook a crossover and subs to a PA...
start here:

http://en.wikipedia.org/wiki/Sound_reinforcement_system
by acorkos
Sat Jan 23, 2010 4:04 pm
Forum: Moog Music General Topics Forum
Topic: MFB Step64 CV circuit loading
Replies: 8
Views: 1498

Re: MFB Step64 CV circuit loading

...may be putting too much of a load on the Step64's output circuit, as the pitch ends up being about a half step below what it should be, and tends to wander when playing a sequence. Has anyone else experienced this? Can it be overcome? my step64 behaves similarly with my modular under certain con...
by acorkos
Thu Jan 21, 2010 12:22 am
Forum: Taurus, Minitaur & Sirin
Topic: T3 amplification
Replies: 55
Views: 18141

a sub might get you a couple more Hz lower than the 8x10...but i'm not sure enough to really hear (or feel) to justify the expense and extra space the sub occupies. i would try out the rig you have first and see if that alone gives you a stiffy...and if so, i would say your rig is complete without t...
by acorkos
Mon Jan 18, 2010 5:47 pm
Forum: Moogerfooger Forum
Topic: Mic with Ring Mod
Replies: 9
Views: 2721

that mixer has no inserts use aux B....post fader for effects. -connect aux B send jack to input of the ring mod with instrument cable -output of the ring mod to aux B return with instrument cable -tweak the aux B return pot for good signal-to-noise -adjust the amount of effect in the channel you're...
by acorkos
Mon Jan 18, 2010 11:35 am
Forum: Little Phatty & Slim Phatty Forum
Topic: When power up my LP all the energy in my home goes down!
Replies: 3
Views: 1032

just don't plug it in and you'll be fine

















just kidding...sounds like the mains wiring is short circuited inside the unit. send it back or get it fixed.