Search found 1579 matches

by latigid on
Tue Jun 21, 2016 5:15 pm
Forum: Moog Music General Topics Forum
Topic: MIDI Freezing/detuning Moog Gear [Help}
Replies: 2
Views: 887

Re: MIDI Freezing/detuning Moog Gear [Help}

Two quick guesses are that you are suffering some sort of MIDI loop or your interfaces aren't up to it (I had lag problems with a simple 2*2). Try just one MIDIsport, try connecting less devices at once to narrow down the problem, and try disconnecting the MIDI out from the synths (one at a time) ba...
by latigid on
Mon Jun 13, 2016 2:36 pm
Forum: Minimoog Forum
Topic: Minimoog voyager select series ..audio
Replies: 2
Views: 1156

Re: Minimoog voyager select series ..audio

Are both outputs connected? Is the right output connected by mistake? In dual low pass mode, try with the left output only -- do the cutoff and spacing controls work properly? Now try the right output. In high pass--low pass mode, do you get proper band pass when adjusting the cutoff and spacing con...
by latigid on
Tue Jun 07, 2016 5:25 pm
Forum: Minimoog Forum
Topic: Has the Voyager no sustain pedal facility?
Replies: 6
Views: 3220

Re: Has the Voyager no sustain pedal facility?

There's an ENV KEYBOARD ON/EXTERNAL switch on the front panel; (I don't have a Voyager with me) you switch that on for every patch you need, and plug a footswitch into ENV GATE. For legato modes, you'd want to configure your patches as single trigger not multi trigger and with non-zero sustain so th...
by latigid on
Mon Jun 06, 2016 3:14 pm
Forum: Minimoog Forum
Topic: Has the Voyager no sustain pedal facility?
Replies: 6
Views: 3220

Re: Has the Voyager no sustain pedal facility?

Well, it has a trigger input for the EGs, so an option is to trigger and hold the pedal, which will maintain the "sustain" level as long as the switch is down. You have an analogue monosynth, not a piano/home organ so you shouldn't expect the same behaviour! What exactly would you like the pedal to ...
by latigid on
Sun Jun 05, 2016 11:23 am
Forum: Moog Music General Topics Forum
Topic: µA726
Replies: 5
Views: 2797

Re: µA726

Surprise surprise, the Doepfer A-111-2 uses a 3340; Dieter Doepfer was a main influence in getting these CEM chips reissued.
by latigid on
Sat Jun 04, 2016 7:38 pm
Forum: Moog Music General Topics Forum
Topic: µA726
Replies: 5
Views: 2797

Re: µA726

I don't have practical experience with this chip as I've never designed with it, but I've listened in on quite a few discussions at MuffWiggler. Before rumours (and they're just that at the moment; there's no confirmation that this will happen) of a new run of 726s, there were people looking into pl...
by latigid on
Thu Jun 02, 2016 9:52 am
Forum: Moog Music General Topics Forum
Topic: Will new Model D parts be available to vintage Mini owners?
Replies: 32
Views: 5206

Re: Will new Model D parts be available to vintage Mini owne

On the silicon side, 3046 is (barely) still available, at least in SOIC or some other SMT package. u726s are basically unobtainium, but there is a guy on MuffWiggler looking at getting some vactrols (full of naughty cadmium) and perhaps u726s after. The French Minimoog clone has a dual FET (LS3954),...
by latigid on
Mon May 23, 2016 4:04 am
Forum: Moogerfooger Forum
Topic: MF-108M malfunction: All leds are yellow
Replies: 2
Views: 1020

Re: MF-108M malfunction: All leds are yellow

Normally this isn't a good sign, there's a few known instances of MuRF pedals lighting up yellow/orange which meant something had gone awry with the CPU/MCU. Definitely look at sending it back for repair under warranty. With luck it could be something in the power supply section caused by an intermi...
by latigid on
Sun May 22, 2016 3:57 am
Forum: Minimoog Forum
Topic: Select/EB - Black LCD cover / faceplate?
Replies: 2
Views: 1084

Re: Select/EB - Black LCD cover / faceplate?

You might consider getting source files from Moog or measuring up the original plastic part, then getting your own cut from one of the laser services like Ponoko or Formulor. You could do infill engraving or leave it blank. I bet the design is very simple and would be very quick and cheap to do.
by latigid on
Fri May 20, 2016 3:45 am
Forum: Moogerfooger Forum
Topic: Here is your Moog sequencer:
Replies: 2
Views: 1483

Re: Here is your Moog sequencer:

Apparently these are (for the moment) only able to be built at Moogfest with an engineer ticket.

http://www.muffwiggler.com/forum/viewto ... c&start=25
by latigid on
Thu May 19, 2016 4:46 am
Forum: Moogerfooger Forum
Topic: Here is your Moog sequencer:
Replies: 2
Views: 1483

Here is your Moog sequencer:

https://www.instagram.com/p/BFjbTB2iRwD/


BFAM, or Brother from another mother.


Looks like a companion module to the M-32, built in osc, filter and EG just from that partial image.


[also here http://forum.moogmusic.com/viewtopic.php?f=19&t=25622]
by latigid on
Thu May 19, 2016 4:44 am
Forum: Moog Music General Topics Forum
Topic: The Global Synthesizer Project
Replies: 10
Views: 2423

Re: The Global Synthesizer Project

Folks, this is real hardware:

https://www.instagram.com/p/BFjdGZEiR1H/


From another post apparently it's just the art project and not slated for general release.


More to come as Moogfest starts!
by latigid on
Tue May 10, 2016 4:28 pm
Forum: Modular Forum
Topic: 921 clamping point?
Replies: 14
Views: 4340

Re: 921 clamping point?

Thanks Eric, this one's much clearer.

Seems like the clamp control acts on the positive slope up to 12 o'clock then starts working on the negative portion?

Cool sounds, enjoy those lovely oscs!
by latigid on
Tue May 10, 2016 2:14 am
Forum: Modular Forum
Topic: 921 clamping point?
Replies: 14
Views: 4340

Re: 921 clamping point?

You're certainly getting some wavefolding going on there! It's still a bit too hard to say exactly what the clamp is doing: is it a phase shift or some sort of voltage threshold (comparator)? Is the master 901 running at an independent frequency? Or is it one big feedback loop? Might a more straight...
by latigid on
Mon May 09, 2016 2:23 am
Forum: Modular Forum
Topic: 921 clamping point?
Replies: 14
Views: 4340

Re: 921 clamping point?

I'll have to leave Eric to detail the results, but apparently the 921 doesn't do regular hard (reset) sync, but operates on a phased lock loop (PLL) system. While this can approximate synchronisation (e.g. MF-107 Freqbox) it's more likely to emphasise certain harmonics relative to phase.