Search found 176 matches

by Markyboard
Wed Dec 11, 2019 9:05 am
Forum: Grandmother, Mother-32 & DFAM
Topic: Matriarch VCO1 is out of tune on F#1 key
Replies: 1
Views: 7

Re: Matriarch VCO1 is out of tune on F#1 key

Strange that it's only the F#. Can you test it again using midi to help narrow down the problem?
by Markyboard
Wed Dec 04, 2019 9:21 am
Forum: Moog Music General Topics Forum
Topic: where is everybody?
Replies: 18
Views: 410

Re: where is everybody?

Face who?
by Markyboard
Thu Nov 28, 2019 10:18 am
Forum: Moog One
Topic: Memorymoog Frozen on 00
Replies: 3
Views: 171

Re: Memorymoog Frozen on 00

Hi- There are reset pins on the Digital Board. You short them together as I recall and that will force a system reset. It’s documented in the manual but if you have trouble finding them post again. Also someone mentioned wrapping their PROMs in aluminum foil. I was completely surprised and skeptical...
by Markyboard
Mon Nov 25, 2019 7:05 pm
Forum: Minimoog Forum
Topic: Note priority on incoming midi not working?
Replies: 1
Views: 74

Re: Note priority on incoming midi not working?

I’m on OS 3.6 and just tested low, high and last note priority. I recorded into Reaper as well as playing fast runs on my controller. No problem with either. I assume you have local off? If not you should do so to see if it makes a difference. Otherwise I don’t see any harm in reloading the OS. Howe...
by Markyboard
Sat Nov 23, 2019 1:00 pm
Forum: Moog Music General Topics Forum
Topic: Voyager Problems
Replies: 1
Views: 106

Re: Voyager Problems

Hi-

Were the filter and resonance knobs working before you changed out the multiplexers? Which specific multiplexers did you change? I don't believe this will be easy or even possible to solve on line but we can try.
by Markyboard
Wed Nov 20, 2019 7:56 am
Forum: Moog Music General Topics Forum
Topic: Prodigy release trouble
Replies: 1
Views: 74

Re: Prodigy release trouble

Hmmm...don't think you're care'n .... about this very unique problem:

viewtopic.php?f=1&t=33070
by Markyboard
Tue Nov 12, 2019 12:24 pm
Forum: Minimoog Forum
Topic: Voyager Midi In/Midi Out Problem upon restart?
Replies: 6
Views: 156

Re: Voyager Midi In/Midi Out Problem upon restart?

I concur with Till. Global settings should just save without doing anything extra. Have you tried power cycling with your midi cables disconnected? Maybe some errant sysex message is getting in? Otherwise I'd check to see what other master or panel settings are not being saved.
by Markyboard
Sun Nov 10, 2019 9:24 am
Forum: Minimoog Forum
Topic: Moog Voyager RME - Unable to update to v.3.5
Replies: 3
Views: 189

Re: Moog Voyager RME - Unable to update to v.3.5

Did you select “Receive Update” under the Master menu? You didn’t mention that you had. RECEIVE UPDATE The RECEIVE UPDATE utility allows you to upgrade the Voyager’s Operating System. Updates are available from our website (www.moogmusic.com) and are found in Minimoog Voyager ‘Software’ section. Ins...
by Markyboard
Sun Nov 10, 2019 7:49 am
Forum: Moogerfooger Forum
Topic: Midi Murf 200 freq resonant band anomaly
Replies: 2
Views: 148

Re: Midi Murf 200 freq resonant band anomaly

Hi- From the user manual: +9V POWER INPUT jack – accepts +9VDC unregulated 300 mA power adapter with positive center. I can't imagine why the power supply would cause the symptom you described. Assuming you're power supply meets or exceeds the spec above (more current capability) it shouldn't matter...
by Markyboard
Tue Nov 05, 2019 7:20 pm
Forum: Minimoog Forum
Topic: Voyager waveform pot/range calibration
Replies: 12
Views: 389

Re: Voyager waveform pot/range calibration

Hi Igor- It could be that the potentiometer is degraded. In case you’re unfamiliar it’s the mechanism that the front panel knob turns providing a variable resistance based on its position. Being a mechanical device they are prone to wearing out over time. Is it possible for you to get hold of a mult...
by Markyboard
Mon Nov 04, 2019 9:03 am
Forum: Moog One
Topic: do the Moog One knob values "jump" when you move them, after loading a patch?
Replies: 9
Views: 858

Re: do the Moog One knob values "jump" when you move them, after loading a patch?

On all my hybrid synths (Voyager RME, Andromeda, Minitaur), I have to set them to pass thru when I gig with high volume PA. The vibrations from the PA can actually cause the wipers on the pots to move and the instrument will go into "self edit" thinking that the user moved a pot. Yikes! You might w...
by Markyboard
Sun Nov 03, 2019 2:27 pm
Forum: Minimoog Forum
Topic: Voyager waveform pot/range calibration
Replies: 12
Views: 389

Re: Voyager waveform pot/range calibration

Hmmm...OK interesting. I'm sure you can understand the sentiment "if only I had that patient on a table in front of me" :wink: . It's really difficult to troubleshoot remotely and so I or anyone else for that matter can only give you our best advice based on the results of the last attempt. Here's m...
by Markyboard
Sun Nov 03, 2019 1:11 pm
Forum: Controllers Forum
Topic: where is “MP-201 V2.0 Firmware?
Replies: 5
Views: 1354

Re: where is “MP-201 V2.0 Firmware?

Here's the latest Windows version. Sorry don't have the Mac version.

I believe you may need to start with V2.0 ( not certain) so here it is:
MP201_v2_WIN.zip
(696.9 KiB) Downloaded 13 times

Here is the V2.1 version:
MP201_v2_1_Update_WIN.zip
(299.94 KiB) Downloaded 14 times
by Markyboard
Sat Nov 02, 2019 7:23 pm
Forum: Moog One
Topic: do the Moog One knob values "jump" when you move them, after loading a patch?
Replies: 9
Views: 858

Re: do the Moog One knob values "jump" when you move them, after loading a patch?

Good point Till. I guess in the home studio I just want my pots to respond immediately despite the jump. I know others who swear by endless encoders for the same reason you mention; I just prefer pots and the visual position advantage. Also I use CV expression pedals with at least 1 and often 2 para...
by Markyboard
Sat Nov 02, 2019 11:56 am
Forum: Moog One
Topic: do the Moog One knob values "jump" when you move them, after loading a patch?
Replies: 9
Views: 858

Re: do the Moog One knob values "jump" when you move them, after loading a patch?

Since we're talking about it here does anyone actually use Pass Thru mode? It's a coin toss which way you initially turn the pot, easy to overshoot and even difficult at times to find the programmed value. I have it on the Poly Evolver and never use it. Am I missing something as far as it's usefulne...