Hello,
I believe you would be able to put everything to the same midi Channel and then just use the volume on each unit to control which one you hear while playing.
Midi cable from Controller to DS61 to Minitaur.
Hope that helps.
GD
Search found 42 matches
- Mon Jan 03, 2022 9:23 am
- Forum: Taurus, Minitaur & Sirin
- Topic: MIDI Foot Pedals and Juno DS-61 w/ Minitaur
- Replies: 2
- Views: 14913
- Sat Oct 02, 2021 6:32 am
- Forum: Taurus, Minitaur & Sirin
- Topic: Taurus 1 decay problems
- Replies: 1
- Views: 7554
Re: Taurus 1 decay problems
Sounds like you have contamination (flux) around the sample and hold circuit for the keyboard. Or you have a defective part in the sample and hold circuit area.
GD
GD
- Tue Feb 02, 2021 11:50 am
- Forum: Moog Music General Topics Forum
- Topic: Can you identify this long lost Memorymoog Plus update kit?
- Replies: 3
- Views: 4800
- Wed Dec 16, 2020 11:33 am
- Forum: Moog Music General Topics Forum
- Topic: Memorymoog "DEAD OSC" on all voice cards OSC3
- Replies: 39
- Views: 11746
Re: Memorymoog "DEAD OSC" on all voice cards OSC3
Hello, If you tune them by ear its a lot easier. Disable the auto tune (C-6) and enable only that voice (C-4) and tune it to a reference oscillator to start. Adjust the scale, but don't worry about retuning the initial frequency until you have at least a decent octave range set. Then test at 2 octav...
- Fri Sep 27, 2019 2:55 pm
- Forum: Moog Music General Topics Forum
- Topic: Moog Memorymoog v. 2.5 firmware
- Replies: 3
- Views: 4310
Re: Moog Memorymoog v. 2.5 firmware
Hello, I don't have the files, but I have some chips if you wanted to go directly to the chips. You can send me a PM.
- Fri Sep 27, 2019 2:54 pm
- Forum: Moog Music General Topics Forum
- Topic: Micromoog parts source needed
- Replies: 5
- Views: 9539
Re: Micromoog parts source needed
You really need to check the ground on the ribbon controller. If that's loose the ribbon won't work. However I can rebuild them if you need to. Send me a PM.
- Fri Sep 27, 2019 2:52 pm
- Forum: Moog Music General Topics Forum
- Topic: Minimoog Squirrelly Keys!
- Replies: 2
- Views: 2468
Re: Minimoog Squirrelly Keys!
I would check your cinch Jones keyboard connector. Those things can get squirrelly when you take them apart and put them back together if they're not clean.
- Sat May 05, 2018 11:38 pm
- Forum: Moog Music General Topics Forum
- Topic: MG-1 won't play B, C and C#
- Replies: 8
- Views: 5433
Re: MG-1 won't play B, C and C#
Have you scoped out the top active divider yet?
The trigger for the mono section is generated from the poly section.
So if you have notes out on the TOC, the mono notes will not trigger.
Oscilloscope is your best friend for testing those.
GD
The trigger for the mono section is generated from the poly section.
So if you have notes out on the TOC, the mono notes will not trigger.
Oscilloscope is your best friend for testing those.
GD
- Tue Mar 21, 2017 10:36 am
- Forum: Moog Music General Topics Forum
- Topic: My Source is crazy, but in a catatonic sort of way
- Replies: 25
- Views: 11021
Re: My Source is crazy, but in a catatonic sort of way
Hello,
I have them.
Why do you suspect the ROM is out?
GD
I have them.
Why do you suspect the ROM is out?
GD
- Tue Mar 07, 2017 9:12 am
- Forum: Modular Forum
- Topic: 1150 Ribbon Controller Slider replacement
- Replies: 2
- Views: 2887
Re: 1150 Ribbon Controller Slider replacement
Hello,
Your best bet is to repair the existing pot.
I do this all the time on vintage pots.
You will need to find the same make pot at any value, and open them up and replace the slider stem.
Hope that gives you some ideas.
GD
Your best bet is to repair the existing pot.
I do this all the time on vintage pots.
You will need to find the same make pot at any value, and open them up and replace the slider stem.
Hope that gives you some ideas.
GD
- Tue Mar 07, 2017 9:09 am
- Forum: Moog Music General Topics Forum
- Topic: multimoog missing osc b pcb
- Replies: 4
- Views: 3109
Re: multimoog missing osc b pcb
Hello,
You might be missing more than the tandem board if you have open holes in the top of the unit.
There are 2 small circuit boards in the Multimoog.
One is the tandem board and the other is the (pot/switch) top board.
You will need them both.
Good luck on your search/project.
GD
You might be missing more than the tandem board if you have open holes in the top of the unit.
There are 2 small circuit boards in the Multimoog.
One is the tandem board and the other is the (pot/switch) top board.
You will need them both.
Good luck on your search/project.
GD
- Wed Feb 08, 2017 5:32 pm
- Forum: Moog Music General Topics Forum
- Topic: Help! The Source is killing me!!!
- Replies: 21
- Views: 11076
Re: Help! The Source is killing me!!!
Hello,
What Parts in the touch panel matrix circuit have you tried so far?
GD
What Parts in the touch panel matrix circuit have you tried so far?
GD
- Wed Feb 08, 2017 5:16 pm
- Forum: Moog Music General Topics Forum
- Topic: Moog System 35 from Hell!!!!
- Replies: 6
- Views: 4881
Re: Moog System 35 from Hell!!!!
Hello, I would try to isolate the issue first by removing the 921A and 921B (the most troublesome one) from the cabinet and putting it on your bench with another power supply and connectors. Based on the schematics, it only requires +12 -6 Gnd and then the summing node, reference ground and the PW i...
- Fri Jan 06, 2017 11:16 am
- Forum: Moog Music General Topics Forum
- Topic: MemoryMoog latest firmware for non-plus
- Replies: 13
- Views: 7415
Re: MemoryMoog latest firmware for non-plus
Thanks RL!
I will do that on my next update install.
GD
I will do that on my next update install.
GD
- Wed Dec 21, 2016 12:07 am
- Forum: Moog Music General Topics Forum
- Topic: MemoryMoog latest firmware for non-plus
- Replies: 13
- Views: 7415
Re: MemoryMoog latest firmware for non-plus
Hi RL,
What should they be, for that firmware then? Just curious?
Thanks.
GD
What should they be, for that firmware then? Just curious?
Thanks.
GD